Controlled-products-systems-group SPX-7200 Bedienungsanleitung

SPX-7200_MAN_082112SPX-7200 SeriesSuprex® Reader Extender - EthernetOperations ManualEXP-2000SPX-7200

3. Select the device to be configured with a mouse click. The device will highlight in blue as shown above when selected. Verify which device is to

Setting IP Address - SPX-7200 5. After the IP addresses have been assigned to both units, select the CENTRAL unit in the device list.6: Select the Te

Setting IP Address - SPX-7200 7. You should now have an open window like this. Press the ENTER key to enter setup mode.8. A list of options will be

Setting IP Address - SPX-7200 9. All of the parameters will have been set as factory default, it will be necessary to set the address of the REMOTE u

Cypress Suprex® SPX-7200 Series - Door Strike and LED I/ONote: The LED and Door Strike operation of the Ethernet Suprex® differs from previous Suprex®

InputJumper to ground to testLED InSuprex® CentralGroundSuprex® RemoteOutputLED OutRed arrow denotes direction of command signalCypress Suprex® SPX

Cypress Suprex® SPX-7200 Series - Relay ControlsRed arrow denotes direction of command signalRelay 1 INInput SignalRelay 1 N.O.Relay 1 ComRelay 1 N.C.

Relay 3 functions as an Alarm relay and monitors the condition of the communication link between the Central and Remote units. Relay 3 is activated w

Door N.C. ContactRex N.O. Contact1K1KRelay 2 N.O.Relay 2 ComRelay 2 N.C.Relay 1 N.O.Relay 1 ComRelay 1 N.C.Ground Aux inNot usedNot usedexp (+)exp (-)

Before using EXP-2000 Expansion modules with the SPX-7200 system, it will be necessary to perform a short configuration process. This process determin

This manual covers the operation and setup of the Cypress Suprex® SPX-7200 Ethernet series units. Overview:The SPX-7200 series of Ethernet solutions

Wiegand DataRS-485 Link - Multi-dropCard ReaderControl and I/OACSSPX-7200C (1)EXP-2000C (3)EXP-2000C (2)EXP-2000R (2)EXP-2000R (3)SPX-7200R (1)Cypres

Cypress Suprex® Series - Wiegand Expansion ModulePanel “Central” interfaceSee EXP-2000 Manual for further setup instructions*EXP-2000Central Unit8 t

Cypress Suprex® Series - Wiegand Expansion ModuleReader/Door “Remote” interfaceAdditionalEXP Modules*EXP-2000Remote Unit8 to 16 VDC InGroundRLY2 N.O.

1 - 8 to 16 VDC In 2 - GroundStatus LED1 - exp (+)2 - exp (-)3 - +5 VDC out4 - Prog Res 45 - Prog Res 36 - LED In 7 - D1/Data out 8 - D0/Clk out

SPX-7200 Series CentralQuick Reference For Typical ConnectionsDCPower SupplyAccessControl Panel+8 to +16 VDCGroundDiagnostic LEDR1 Input Controls Stri

Cypress Suprex® SPX-7200 Enclosure Dimensions1.702.003.080.800.803.154.45ø0.20 X 4

LED Diagnostic Indicator:The LED Diagnostic indicator provides information on the operational status of the unit.If the units are not communicating, v

Bench Testing:Before installing the units in the field they should be assembled and tested at a convenient “Bench top” location. This will make it ea

Cypress Suprex® SPX-7200Changing the IP Address In many cases it may be necessary to change the addressing to be compatible with an existing network.

Setting IP Address - SPX-7200 1. Start the Lantronix XPort Installer software. The startup screen is shown above.2. Click the “Search” button, after