Controlled-products-systems-group DD Bedienungsanleitung PDF herunterladen

INSTR,CODE SET,DELTA-3

Linear P/N: 200108 E

Size: 8.500" x 11.000"

Material: 20 Lb. Mead Bond

Ink: Black

Scale: 1-1

DELTA-3

SYSTEM

Single-channel Digital

Receiver and

Transmitter

Code Setting and

Installation Instructions

(800) 421-1587

•

www.linearcorp.com

DESCRIPTION

The Delta-3 digital receiver and transmitter is a single-channel wireless radio

control designed for use with automatic garage/gate operators and access

control systems. All Delta-3 products (on the same frequency) can be mixed

and matched to suit your individual needs.

The Delta-3 radio format provides 256 different digital codes. The codes are

set using the 8-position coding switches in the units.

☞

Caution: All transmitters and receivers should be

recoded prior to operation.

In order to avoid the possibility of duplicating codes in adjacent systems,

factory set codes should not be used. In addition, among the valid codes

available, four others should not be used. These include: all keys set ON or

OFF and keys set alternating ON/OFF.

Where a number of receivers are to be installed in close proximity (as in an

apartment complex), install receivers at least 5 feet apart. If receivers are

installed closer than 5 feet apart, blocking may occur.

After completing an installation, operate the transmitter outside the building and

check to see that the coded signal being used does not interfere with neighboring

garage door operators and/or security systems. If interference is detected, select

another code and check coded signal again. Repeat if necessary.

Step 1

Locate Coding Switches.

Locate the digital coding switch

for the receiver which is recessed in the center of the back of the case.

The transmitter coding switch is accessed by removing the battery

access door located on the back of the transmitter case. The keys

are numbered 1 through 8. The switches in the receiver must match

the switches in all transmitters used to operate the receiver.

Step 2

Code Transmitter and Receiver.

Use a paper clip or

other pointed object (except a pencil or pen) to pick any

combination of ON/OFF codes and set them on switch keys 1

through 8 on the receiver and transmitter. The ON position is when

the top of the switch is down. The OFF position is when the top of

the switch is up and the bottom is down.

Step 3A

Connecting Receiver (using transformer power).

Where it is not feasible to obtain power from the operator, connect

a Model 524 transformer (accessory) to the receiver as shown below.

Then plug the transformer into a convenient (unswitched) 110 VAC

outlet.

Step 3B

Connecting receiver (using operator power).

Connect the receiver to the garage door or gate operator as shown

in the diagram. Power will be supplied from the operator.

Step 4

Remote Mounting.

A mounting clip is packaged with each

receiver. To install the receiver, attach the clip to the mounting

surface with screws. Position the two rectangular holes on the

back of the receiver over the clip and snap the receiver down into

place.

LINEAR LIMITED WARRANTY

This product is warranted to the consumer against defects in material

and workmanship for one year from the date of purchase. This

warranty applies to first retail buyers of new devices. Warrantor will

repair, or at its option, replace, any device it finds that requires service

under this warranty, and will return the repaired or replaced device to

the consumer at the warrantor’s cost. For warranty service and

shipping instructions contact warrantor at the phone number shown

below. Devices must be sent to warrantor for service at owner’s

expense. The remedies provided by this warranty are exclusive.

Implied warranties under state law are to the one year period of this

written warranty. Some states do not allow limitations on how long an

implied warranty lasts, so the above limitation may not apply to you.

In order to be protected by this warranty, save your proof of purchase

and send copy with equipment should repair be required. This

warranty gives you specific legal rights, and you may also have other

rights which vary from state to state.

All products returned for warranty service require a Return

Product Authorization Number (RPA#). Contact Linear

Technical Services at 1-800-421-1587 for an RPA# and other

important details.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and fill an

important need in portable wireless signaling. However, there are

some limitations which must be observed.

✶

For U.S. installations only: The radios are required to comply with FCC Rules

and Regulations as Part 15 devices. As such, they have limited transmitter

power and therefore limited range.

✶

A receiver cannot respond to more than one transmitted signal at a time and

may be blocked by radio signals that occur on or near their operating

frequencies, regardless of code settings.

✶

Changes or modifications to the device may void FCC compliance.

✶

Infrequently used radio links should be tested regularly to protect against

undetected interference or fault.

✶

A general knowledge of radio and its vagaries should be gained prior to acting

as a wholesale distributor or dealer, and these facts should be communicated

to the ultimate users.

This device complies with FCC Rules Part 15 and IC Canada Rules

and Regulations. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference and (2) this device

must accept any interference received, including interference that

may cause undesired operation.

24 V RELAY RADIO

PWR

REMOVE

BATTERY

DOOR

TRANSMITTER

CODING SWITCH

RECEIVER

CODING SWITCH

(3) 24 VAC

(1) COM

(2) RELAY

COM

RELAY

24 VAC

MANUAL

PUSHBUTTON

3-TERMINAL

OPERATOR

(1) COM

(2) RELAY

COM

RELAY

24 VAC

MANUAL

PUSHBUTTON

2-TERMINAL

OPERATOR

MODEL 524

TRANSFORMER

DELTA-3 RECEIVER

DELTA-3 TRANSMITTER

SET

1-8

MATCH

1-8

SWITCHES 1, 3, 4, 7 & 8

ARE "ON" 2, 5 & 6 ARE "OFF"

ALL TRANSMITTER SWITCHES

MUST MATCH RECEIVER SWITCHES

MOUNTING CLIP

RECEIVER

MOUNTING

CLIP

MOUNTING HOLES

ON RECEIVER

Inhaltsverzeichnis

Seite 1 - Transmitter

INSTR,CODE SET,DELTA-3Linear P/N: 200108 ESize: 8.500" x 11.000"Material: 20 Lb. Mead BondInk: BlackScale: 1-1DELTA-3 SYSTEMSingle-channel D

Kommentare zu diesen Handbüchern

Keine Kommentare

Controlled-products-systems-group DD Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Controlled-products-systems-group DD herunter. Controlled Products Systems Group DD User Manual [en] [de] [fr] [es] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Controlled-products-systems-group DD