Controlled-products-systems-group 109773 Bedienungsanleitung

carta riciclata 100%per la naturafor naturerecycled paper 100%ist umweltfreundlich100% Altpapierpara la naturaleza100% papel recicladopapier recyclÈ 1

26RX OP/CLTX OP/CLSAFE++OPENBAOPENOPCLFig. 34Fig. 355.4.2. J7 Terminal board - Power supply (fig. 23)POWER SUPPLY (terminals PE-N-L):PE: Earth connect

27MINI DECPLUSRPF-+FFig. 37Fig. 36Fig. 38Fig. 39TX -FSW - Negative for power supply to photocell transmitters(terminal 11)If you use this terminal for

28F++FORCE:Adjusts Motor thrust. = minimum force = maximum forceOPENING DIRECTION:Indicates the gate opening movement andmakes it possible not to chan

29Display Function Default Display Function DefaultOPENING PHOTOCELLS LOGIC:Select the tripping mode of the openingphotocells.They operate for the ope

30FC2FC1Fig. 40Fig. 426.2. DEFINITION OF OPENING DIRECTION AND OPERATIONOF LIMIT-SWITCH LEDSPower up the system and set the opening direction on thebo

31MFig. 46Fig. 45Fig. 44Fig. 437. FINAL OPERATIONSAt end of installation, apply the danger sticker on the top ofthe cover (Fig. 45).6.7. CHECK OF STOP

32Fig. 50Fig. 49Fig. 48Fig. 529. RESTORING NORMAL OPERATIONTo prevent an involuntary pulse from activating the gate during themanoeuvre, cut power to

33"PA"cigoL SESLUPSUTATSETAGA-NEPOB-NEPOPOTSSECIVEDYTEFASGNINEPOSECIVEDYTEFASGNISOLCECIVEDYTEFASLC/POECIVEDYTEFASEGDEDESOLCsesolcdnafaelehts

34(1) If maintained, it prolongs the pause until disabled by the command (timer function) (3) During the partial opening cycle, an OPEN A pulse causes

USER’S GUIDEAUTOMATED SYSTEM 746Read the instructions carefully before using the product and keepthem for future consultation.GENERAL SAFETY REGULATIO

181) ATTENTION! To ensure the safety of people, it is important that you readall the following instructions. Incorrect installation or incorrect use

19MODEL 746Power supply (Vac +6% -10% 50-60Hz) 230Absorbed power (W) 300Reduction ratio 1 : 30Type of pinion Z20 - Z16Rack Module 4 - step 12.566Max.

20Fig. 4Fig. 5Fig. 6Fig. 7Fig. 2Fig. 32. DIMENSIONS3. ELECTRIC EQUIPMENT (standard system)To make the connections efficiently, allow the cables toproj

21ABFig. 8Fig. 12Fig. 10Fig. 11Fig. 9Fig. 135) Secure the gearmotor to the foundation plate, tightening thenuts as in Fig.12.6) Prepare the operator f

22Fig. 15Fig. 16Fig. 19Fig. 21Fig. 20Notes on rack installation• Make sure that, during the gate travel, all the rack elements donot exit the pinion.•

23–+DLLedF1J1J2LedJ5FJ7F2J8J6Fig. 22DL SIGNALLING AND PROGRAMMING DISPLAYLed INPUTS STATUS CONTROL LEDJ1 LOW VOLTAGE TERMINAL BOARDJ2 CONNECTOR FOR DE

24SAFE++OPEN BOPEN AOPCLJ1J5BLUESAFE++OPENBAOPENOPCLSAFE++OPENBAOPENOPCLSAFE++OPENBAOPENOPCLFig. 23Fig. 24Fig. 25Fig. 26Fig. 27Fig. 285.4.1. Connecti

25SAFE++OPENBAOPENOPCLRX OPTX OPSAFE++OPENBAOPENOPCLRX OP/CLTX OP/CLRX OP TX OPSAFE++OPENBAOPENOPCLSAFE++OPENBAOPENOPCLSAFE++OPENBAOPENOPCLFig. 30Fig.