Controlled-products-systems-group 361LM Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Controlled-products-systems-group 361LM herunter. Controlled Products Systems Group 361LM Manuel d'utilisation [de] Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 8
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
To prevent possible SERIOUS INJURY or
DEATH from a moving gate or garage door:
ALWAYS keep remote controls out of
reach of children. NEVER permit children
to operate, or play with remote control
transmitters.
Activate gate or door ONLY when it can be
seen clearly, is properly adjusted, and
there are no obstructions to door travel.
ALWAYS keep gate or garage door in sight
until completely closed. NEVER permit
anyone to cross path of moving gate or
door.
INTRODUCTION
This product is for use with gate operators, commercial door operators and any LiftMaster
®
product
that uses a 315 MHz fixed code. The single-button remote control will activate one device, the
2-button remote control will activate up to 2 devices, and the 3-button remote control will activate
up to 3 devices.
Model 361LM & 361LMC
Model 362LM & 362LMC
Model 363LM, 363LMC,
333LM, & 333LMC
Locate the Dip Switches on Your Remote Control
BEFORE YOU BEGIN
Locate the Smart/Learn Button for Your Product
Single-Button and 3-Button
Remote Controls:
Slide the battery cover open to access the dip
switches in the remote control.
2-Button Remote Control:
The 2-button remote control has two sets of
dip switches.
Slide the battery cover open to access the dip
switches for the smooth button. Remove the
screw on the back of the remote control and
remove the cover by pressing the tab. This will
access the dip switches for the ribbed button.
+
0
123456789
+
0
123456789
+
0
123456789
Tab
1
Single and 3-Button Remote Controls
2-Button Remote Controls
NOTE: Your product may look different than
the products illustrated.
The Smart/Learn button is typically located on
the logic board of the operator or external
receiver. Refer to your product owner’s manual
for the exact location of the Smart/Learn
button.
Smart/Learn Button
Seitenansicht 0
1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - BEFORE YOU BEGIN

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:• ALWAYS keep remote controls out of reach of children. NEVER permit ch

Seite 2 - PROGRAMMING

SET THE DIP SWITCHES1Press and release the Smart/Learn button on your product. The LED will light.2Within 30 seconds press and hold the button on the

Seite 3 - PROGRAMMING MODEL 333LM ONLY

PROGRAMMING MODEL 333LM ONLYInstall the control station and receiver where the door is visible, but away from the door and its hardware. When a receiv

Seite 4 - REPLACEMENT PARTS

THE REMOTE CONTROL BATTERYTo prevent possible SERIOUS INJURY or DEATH:• NEVER allow small children near batteries.• If battery is swallowed, immediate

Seite 5 - AVERTISSEMENT AVERTISSEMENT

INTRODUCTIONCe produit est destiné à être utilisé avec des dispositifs de fermeture de barrières, des dispositifs de fermeture de porte commerciaux et

Seite 6 - PROGRAMMATION

RÉGLAGE DES COMMUTATEURS DIP1Appuyez et relâchez le bouton Intelligent/d’apprentissage de votre produit. La DEL s’allumera.2Dans les 30 secondes, main

Seite 7

PROGRAMMATION DU MODÈLE 333LM UNIQUEMENTInstaller le poste de commande et le récepteur là où la porte est visible mais à l’écart de la porte et de ses

Seite 8

LES PILES DE TÉLÉCOMMANDEPour prévenir d’eventuelles BLESSURES GRAVES ou la MORT :• Ne JAMAIS laisser de petits enfants à proximité des piles.• Aviser

Kommentare zu diesen Handbüchern

Keine Kommentare