Controlled-products-systems-group SLIDESMART DC 10F Bedienungsanleitung Seite 115
- Seite / 148
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Smart DC Controller Troubleshooting
Revision D Reference 6-17
Table 6-1. Smart DC Controller - Troubleshooting
Display Description
Possible Causes Solutions
Condition Alert, Error or Fault
SAFE MODE Safe Mode Alert Occurs when either the edge sensor or Inherent
Entrapment Sensor (IES) has been tripped. In Safe Mode,
the automatic close timer is disabled, but any command
will reset and/or start the gate in motion. Safe Mode clears
when full travel is reached or the RESET button is pressed.
Gate binding, wind, a faulty edge sensor, or worn motor
brushes can cause a false alert.
1. Remove the obstruction.
2. Adjust the IES sensitivity.
3. Correct the gate hardware.
4. Correct faulty edge sensor.
5. Check for worn motor brushes and replace, if
necessary.
ENTRAPMENT MODE Entrapment Mode Alert Occurs when the IES is tripped when the gate is already in
Safe Mode. The operator will not function until it is reset,
which can occur by:
- An Open or Stop command from a push-button control
- Pressing the red button on the side of the operator
- Pressing the RESET button below the display
With any one of these inputs, the operator will return to
Safe Mode. Gate binding or wind can cause a false alert.
1. Remove the obstruction.
2. Adjust the IES sensitivity.
3. Correct the gate hardware.
NO AC POWER No AC Input Power
Advisory only.
AC power is shut off at the source (breaker) or is not
connected. The AC power switch on the operator (lower
rocker switch) is turned off, or the circuit breaker on the
operator has tripped.
1. Turn AC power switch on or connect power
to the operator.
2. Reset the operator circuit breaker or connect
power to AC switch.
3. Reset circuit breaker at electrical panel.
4. Have a licensed electrician check the wiring.
LOW 24VDC Low 24VDC UPS Batteries
Advisory only.
Occurs when the battery voltage has dropped to less than
22V. At this level, the batteries are 80% depleted. Normal
function until 21V.
1. No AC Power. See above item.
2. Wiring / Connector problem - check all
connections. Clean or repair as required.
3. Check battery condition.
4. Smart DC Controller charger failure - check
charger voltage and replace Smart DC
Controller.
5. Transformer failure - replace transformer.
- SlideSmart DC 1
- OMPONENTS 4
- Contents 5
- Introducing SlideSmart DC 9
- ECHNICAL 10
- NSTALLER 11
- Installer's Check List 12
- Safety Requirements 13
- ECONDARY 17
- NTRAPMENT 17
- ROTECTION 17
- Class I 18
- Class II 18
- Class III 18
- Class IV 18
- Class IV A B1, B2, C, D, or E 19
- MERGENCY 20
- & S 21
- NDUSTRIAL 22
- Installation 23
- Pad Condition 24
- Using an Existing Pad 25
- Front Installation 26
- Rear Installation 27
- NPACKING 28
- PUBLICPUBLIC 29
- SECURESECURE 29
- NSTALLATION 30
- Aligning the Chain 31
- Connect red battery wire 32
- Turn DC power ON 32
- WT 0 33
- GATE WEIGHT (LB) 33
- HYSECURITY 34
- GATE CLOSED 34
- Installing the Target Magnet 35
- Chapter 2 39
- Service Outlet 41
- 115VAC, 15A 41
- Wiring 115VAC Power 42
- Wiring 208/230VAC Power 42
- Voltage selector switch 43
- Map Legend 48
- MPORTANT 49
- ONSIDERATIONS 49
- PERATORS 49
- 50Ah batteries 51
- Accessory tray 51
- Post-mounted 51
- Display and Menu Options 53
- CT 0 (OFF) 55
- CLOSE TIMER 55
- Setting the Time and Date 61
- AP 0 (AC LOSS) 62
- UPS FAIL OPEN 62
- LD 5 63
- LCD CONTRAST 63
- User Menu 64
- DS 0 (OFF) 66
- DIAGNOSTIC LOGS 66
- Adjusting Gate Speed 69
- Adjusting the IES Sensitivity 70
- LL 0 (OFF) 71
- LEARN LIMIT 71
- Reinstating Factory Defaults 72
- Smart DC Controller 83
- Terminal 85
- Input Name Use 85
- HY-5A V 87
- (Bold - Default) 88
- Display Meaning 88
- Entrapment Sensor Connections 91
- Manual Push Button Station 92
- No. Name Description 93
- Bi-parting Gate Systems 95
- Slave Master 96
- Master Slave 96
- LL 0 (OFF) 97
- Master and Slave Menu Setup 98
- Reference 99
- USER 1 RELAY 101
- Installing a Lock for 102
- High Voltage 102
- Installer Menu 103
- NSTALLING 104
- ETECTORS 104
- Figure 6-7 106
- PERATION 107
- Other options include: 108
- UPERVISED 109
- ONNECTION 109
- Revision D Reference 6-13 111
- Two Channel Radio Receiver 113
- ONTROLLER 114
- ROUBLESHOOTING 114
- Display Description 115
- Possible Causes Solutions 115
- Alert or Error 121
- Installer 122
- Menu LCD Description 122
- Setting Options 122
- Bold = Factory Settings 122
- SlideSmart Schematics 123
- Figure 6-15 124
- AINTENANCE 125
- Electrical Controls 126
- Mechanical Maintenance 127
- Software Maintenance 127
- 1/16" to 1/8" 128
- EPLACEMENT 129
- General Maintenance 132
- Installation Configurations 133
- SLIDESMART INSTALLATION 134
- SPECIFICATION 134
- Parts & Limited Warranty 145
- G-2 Revision D 146
- April 2010, D0317 147
- PECIFICATIONS 148
Verwandte Produkte und Handbücher für Sicherheit Controlled-products-systems-group SLIDESMART DC 10F
(36 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern