Controlled-products-systems-group SLIDESMART DC 10F Bedienungsanleitung Seite 117
- Seite / 148
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Smart DC Controller Troubleshooting
Revision D Reference 6-19
ALERT 6
LIM NOT RELEASED
Not used on SlideSmart. N/A
N/A
ALERT 7
FREQ SHIFT FAULT
The HY-5A has detected a frequency
change outside the normal range.
Likely causes are poor integrity of loops or metallic objects
within range. This message will also indicate which
detector the alert applies to: Exit Loop (ELD), Inside
Obstruction Loop (IOLD), Outside Obstruction Loop
(OOLD), or Center Loop (CLD) - (User Relay 22).
The loop lead in wires and roadway should be
checked for problems or replaced.
ALERT 8
LOOP SHORTED
The HY-5A has detected a loop
shorted to ground.
Caused by inadequate insulation of loop wires. The loop lead in wires and roadway should be
checked for problems or replaced.
ALERT 9
LOOP OPEN
The HY-5A has detected a lack of
continuity in the loop wire.
Caused by broken loop wire or wire has come unplugged
from detector.
The loop and lead in wires should be checked
for problems or replaced.
ALERT 10
12C BUS ERROR
The Smart DC Controller has
detected a communication error
with a HY-5A vehicle detector.
Caused by removal of HY-5A or lack of integrity of the
socket connection. This message will also indicate which
detector the alert applies to: Exit Loop (ELD), Inside
Obstruction Loop (IOLD), Outside Obstruction Loop
(OOLD), or Center Loop (CLD) - (User Relay 22).
Remove and re-install the HY-5A and press
RESET. Replace the HY-5A, if necessary.
ALERT 11
DETECTOR FAULT
The Smart DC Controller has
detected a problem within an HY-5A
vehicle detector.
Caused by a fault within the HY-5A. This message will also
indicate which detector the alert applies to: Exit Loop
(ELD), Inside Obstruction Loop (IOLD), Outside
Obstruction Loop (OOLD), or Center Loop (CLD) -
(User Relay 22).
Remove and re-install the HY-5A and press
RESET. Replace the HY-5A, if necessary.
ALERT 12
ON TOO LONG
The Smart DC Controller has an
active loop input (HY-5A or box
detector output) for more than 5
minutes.
Caused when the Smart DC Controller sees an active loop
for more than 5 minutes. The “active” loop can be actual or
false. This message will also indicate which detector the
alert applies to: Exit Loop (ELD), Inside Obstruction Loop
(IOLD), Outside Obstruction Loop (OOLD), or Center
Loop (CLD) - (User Relay 22).
Check traffic patterns at the site. The loop and
lead in wires should be checked for problems or
replaced.
ALERT 13
STIFF GATE
The Smart DC Controller has
detected a gate that, over time, has
taken more power to move than it
used to.
Caused by degrading gate hardware or debris in the track.
This alert appears in the history log. It does not have any
effect with regard to opening or closing the gate.
Check and correct gate hardware as required.
ALERT 14
STUCK GATE
The Smart DC Controller has
detected that it cannot move the gate
at all.
Caused by broken gate hardware or ice/snow buildup. Check and correct gate hardware as required.
Table 6-1. Smart DC Controller - Troubleshooting
Display Description
Possible Causes Solutions
Condition Alert, Error or Fault
- SlideSmart DC 1
- OMPONENTS 4
- Contents 5
- Introducing SlideSmart DC 9
- ECHNICAL 10
- NSTALLER 11
- Installer's Check List 12
- Safety Requirements 13
- ECONDARY 17
- NTRAPMENT 17
- ROTECTION 17
- Class I 18
- Class II 18
- Class III 18
- Class IV 18
- Class IV A B1, B2, C, D, or E 19
- MERGENCY 20
- & S 21
- NDUSTRIAL 22
- Installation 23
- Pad Condition 24
- Using an Existing Pad 25
- Front Installation 26
- Rear Installation 27
- NPACKING 28
- PUBLICPUBLIC 29
- SECURESECURE 29
- NSTALLATION 30
- Aligning the Chain 31
- Connect red battery wire 32
- Turn DC power ON 32
- WT 0 33
- GATE WEIGHT (LB) 33
- HYSECURITY 34
- GATE CLOSED 34
- Installing the Target Magnet 35
- Chapter 2 39
- Service Outlet 41
- 115VAC, 15A 41
- Wiring 115VAC Power 42
- Wiring 208/230VAC Power 42
- Voltage selector switch 43
- Map Legend 48
- MPORTANT 49
- ONSIDERATIONS 49
- PERATORS 49
- 50Ah batteries 51
- Accessory tray 51
- Post-mounted 51
- Display and Menu Options 53
- CT 0 (OFF) 55
- CLOSE TIMER 55
- Setting the Time and Date 61
- AP 0 (AC LOSS) 62
- UPS FAIL OPEN 62
- LD 5 63
- LCD CONTRAST 63
- User Menu 64
- DS 0 (OFF) 66
- DIAGNOSTIC LOGS 66
- Adjusting Gate Speed 69
- Adjusting the IES Sensitivity 70
- LL 0 (OFF) 71
- LEARN LIMIT 71
- Reinstating Factory Defaults 72
- Smart DC Controller 83
- Terminal 85
- Input Name Use 85
- HY-5A V 87
- (Bold - Default) 88
- Display Meaning 88
- Entrapment Sensor Connections 91
- Manual Push Button Station 92
- No. Name Description 93
- Bi-parting Gate Systems 95
- Slave Master 96
- Master Slave 96
- LL 0 (OFF) 97
- Master and Slave Menu Setup 98
- Reference 99
- USER 1 RELAY 101
- Installing a Lock for 102
- High Voltage 102
- Installer Menu 103
- NSTALLING 104
- ETECTORS 104
- Figure 6-7 106
- PERATION 107
- Other options include: 108
- UPERVISED 109
- ONNECTION 109
- Revision D Reference 6-13 111
- Two Channel Radio Receiver 113
- ONTROLLER 114
- ROUBLESHOOTING 114
- Display Description 115
- Possible Causes Solutions 115
- Alert or Error 121
- Installer 122
- Menu LCD Description 122
- Setting Options 122
- Bold = Factory Settings 122
- SlideSmart Schematics 123
- Figure 6-15 124
- AINTENANCE 125
- Electrical Controls 126
- Mechanical Maintenance 127
- Software Maintenance 127
- 1/16" to 1/8" 128
- EPLACEMENT 129
- General Maintenance 132
- Installation Configurations 133
- SLIDESMART INSTALLATION 134
- SPECIFICATION 134
- Parts & Limited Warranty 145
- G-2 Revision D 146
- April 2010, D0317 147
- PECIFICATIONS 148
Verwandte Produkte und Handbücher für Sicherheit Controlled-products-systems-group SLIDESMART DC 10F
(36 Seiten)Steelcraft-automotive 402229 5 OVAL SIDE BAR manuals
Owner’s manuals and user’s guides for For the car Steelcraft-automotive 402229 5 OVAL SIDE BAR.
We providing 1 pdf manuals Steelcraft-automotive 402229 5 OVAL SIDE BAR for download free by document types: User Manual
Kommentare zu diesen Handbüchern